How to install window tint

how to install window tint

Jul 17, Tinting the windows of your car, truck or SUV can add style and comfort to your driving experience, as well as helping you protect your interior from light. Jul 30, Wet the outside of the window with the application solution. Roll the film, liner side facing out, onto the glass keeping in mind that the tint will be applied to the interior side of the glass. Press gently down on the film to temporarily hold it in place for trimming. Trim away the excess film and set the remaining roll to the side.

When installing window film, it is recommended that you have a professional install the tint for the best install possible. Discount Window Film. Partial Rolls. Instructions for Window Film and Tint Installation When installing window film, it is recommended that you have a professional install the tint for the best install possible. Tools required: Spray bottle Water Baby Shampoo Utility Knife, with blades Squeegees Scraper, with blades Paper Towels Get the spray bottle with a trigger Squeeze five to ten drops of baby shampoo or liquid soap into a one quart spray bottle.

Novice installers typically need more soap, this way making it more slippery. Too much soap may result in the tint sliding off of the window. Time to dry out can lengthen in colder environments, resulting in the tint sliding off the glass. Each region and tinter utilizes a unique quantity of soap a different amount dependent on water and experience. Each section and tinter utilizes a unique quantity of soap a different amount of shampoo dependent on how to open mkv files on windows 7 and experience.

Fill the bottle how to install window tint the brim with water and shake. Modify the spray nozzle so the spray will be how to install window tint. Clean the windows well. Remove all dirt from the glass surface. Any dirt and dust that is on the glass or frame will be seen. Therefore, be sure to clean and scrape extensively.

Then spray with the soapy water again. Scrape all the dirt, coating, adhesives, oil, paint, and anything else from the window using a scraper or a razor blade. Always be careful when using this to avoid harming yourself. The corners of the window should be cleansed extensively. Use paper towels to dry the glass.

Make sure that any fans are turned off how to install window tint stop dust from getting in the air and entering behind the tint. Clean the surface of the glass a second time. Use the squeegee to remove any extra water. Use a paper towel to clean and dry. Use the soapy solution to spray the whole surface one more time. Measuring the glass surface, cut the tint an inch wider and longer than the surface of the glass.

Always be how to restart skate 3 career xbox when using a cutting knife. Get two pieces of tape, same size. At one corner of the film, stick a piece of tape on either side of the film. Add pressure where the tape is on the film. Pull each piece of the tape outwards in the opposite direction.

The liner should detach away from the film. If not, redo the tape procedure. Spray the adhesive side of the film with the slip solution to add lubricant. Include spraying the edges of the film. To get the window ready for application, spray it with the slip solution. Hold the film from the top corners, lift the film and put the adhesive side on the glass, and move it until it fits properly. Take a look at all views of the window to examine if the application how to install window tint correct to human sight.

Use the solution to spray the outside of the film. Squeegee out the film starting at the top window center and squeegee to the right, then to the left. Then, slowly work your way down the window with horizontal squeegee motions.

Using the cutting knife, trim the tint to fit inside the window propertly. Spray the slip solution over the tint again, and take out the extra water with the squeegee again as well. Use increased pressure to get water out when installing safety film.

Use increased pressure to get water out of the safety film. Squeegee another time if necessary To avoid scraping the tint, spray solution on top of the film Use the squeegee with a paper towel wrapped around it, to remove water from the edges of the glass frame. Finish up by cleaning the work area. Make sure that you picked up all the blades. You now have a window that looks cool, and can protect you against the sun. Xprize Carbon Removal Competition April 13, 0. Search for:. Follow Us on Facebook.

Instructions for Window Film and Tint Installation

Mar 11, Starting at the top and keeping the top edge level, place the wet surface of the film on the wet glass, working down the window. If you have a crisp factory edge on the film, line it along the glass edge and make sure the rest of the film overlaps the window frame. You wont need to trim this edge. Jun 18, AutoZone Tint 9 Months Later - datlovesdat.com of my recommended tint tools! - datlovesdat.com Apron datlovesdat.com

Last Updated: November 17, References. This article was co-authored by Chad Zani. Chad Zani is the Director of Franchising at Detail Garage, an automotive detailing company with locations around the U. Chad is based in the Los Angeles, California area and uses his passion for auto detailing to teach others how to do so as he grows his company nationwide. There are 17 references cited in this article, which can be found at the bottom of the page.

This article has been viewed , times. Usually, tinted car windows block the ultraviolet sunlight rays that can harm your skin. They also offer privacy from people looking into your car. While tinting is a long, time-consuming process, most people can tint their own windows with only a few basic tools. Our Expert Agrees: The simplest method for sizing the tinting is to place it over the outside of the window.

You'll cut the correct size, and then you move the tinting to the inside for adhesion. Make sure you're sizing the tinting in reverse. Tinting only has one usable side, so you need to size and cut the tinting in the opposite direction so that it fits properly on the inside.

To install window tints, first clean the window you're tinting with soapy water and scrape away any dust, lint, and adhesive on it with a razor blade. Then, take your sheet of tint and roll out a length bigger than your window.

Cut the section off with a razor blade or precision knife. Next, spray the outside of your window with soapy water. Hold the tint up over the outside of the window with the adhesive side facing out.

Don't take the cover off of the adhesive yet. Now, press the tint onto the soapy window. Run a heat gun set to low heat over the bubbles and creases, and use the edge of a credit card to smooth out any bumpy sections. Once the tint is perfectly aligned with the window, use a razor blade or precision knife to carefully cut around the edges of your window.

Remove any excess portions that overlap with the frame or trim of the window, and lift the tint off. Take the same tint and move it to the inside of the door. Clean the interior side of the window with soapy water and a razor blade so there's nothing on it that could interfere with the tint. Roll your window down inches 2. Peel the top corner of the adhesive side off. Fit it against the window pane and press down a little. Raise the window up and remove the rest of the adhesive cover.

Press the tint into the glass to fit the window, and use a heat gun and credit card to remove any bubbles or creases.

Repeat this process on any other windows you want to tint in your vehicle. For tips on how to determine which side of the tinting is the adhesive, read on! Did this summary help you? Yes No. Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue. No account yet? Create an account. Edit this Article. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow.

Download Article Explore this Article parts. Tips and Warnings. Things You'll Need. Related Articles. Article Summary. Part 1 of Find a clean, dry work space. You need a clean environment to prevent dust and dirt from mixing with the tinting.

Doing everything indoor is not a bad idea. But if you want to work outside, you should choose a clean and dry place. Remove any stickers or adhesives from the windows. Remove any stickers inside of your car screen and clean off all the adhesives or any sticky things that can create problems with the film sticking on the windows. Remove all the obstructions inside the car that can restrict your process and get in your way.

Finally, vacuum the interior to get rid of dust. Clean up the windows using soapy water and a 1" razor blade. Lower the window slightly so that you can get the top as well. Mix a few drops of dish soap with warm water and spray or wipe it on the window, then use the blade to scrape away all the dirt and grime.

Make sure you clean both sides of the window well, removing everything. Never use Windex, or cleaner with ammonia in it. It will tint your windows purple when you're done. Make sure you get all the edges and seals, and role the window up to get the bottom. You're going to need almost a gallon of soapy water throughout this process. Prepare the water ahead of time to make working easier. A spray bottle is highly recommended. Take a clean rag and dry the window.

Wipe away the soapy water on both sides and dry off the edges as well. If you're using a spray bottle, refill it with more soapy water. A squeegee will help you get the window completely dry. Make sure you get underneath the seals in the interior of the car. Use your finger to get under the seal and remove dirt and dust. Roll the window back up before beginning, but leave your car on.

You'll need to move the window up and down as you work. For now, leave it up. Determine which side of the tint is adhesive. Like a sticker, the tint has a layer that can be peeled off right before adhering it to the window. Make sure, as you work with the tint, that this side is facing you. Part 2 of Spray the outside of the window with soapy water. The water will help the tinting temporarily adhere, but still make it slippery enough to slide around and put into place.

Place the tinting over the outside of the window so that it covers the entire window. Unroll your tinting so that it covers the entire window, with at least " of extra tinting over the edges. The liner the part that will later adhere to the window , should be facing you.

Make sure you do not remove the liner -- you're just sizing and pressing the tinting right now, now adhering it. Cut away a manageable slab of tinting. You should have a few inches of extra tint in every direction, but you don't want to be maneuvering the entire roll of film while working. Use a precision knife or blade to cut a usable square of tinting film from the larger role. Spray the front of the film with water.

Once the tint is cut into a square, it should stick to the water on the outside of the window. You should then spray the tint itself so that the entire thing is covered in a thin layer of soapy water. Take your knife and cut along the bottom and left edges of the window. Simply use the edges of the window to trace your knife across the tinting film. You want a perfectly shaped line to ensure the tint fits. When done, two of the edges should fit perfectly, and the rest should still be square.

As you cut, use the squeegee or your free hand to make sure the film is flush with the window. When done, cut the excess film away and discard. Pull the film 1" towards the left edge.



More articles in this category:
<- How to check ca final registration status online - How to fix print spooler problem->

3 thoughts on “How to install window tint

Add a comment

Your email will not be published. Required fields are marked *

Back to top