How to reignite a gas water heater

how to reignite a gas water heater

How to Light a Pilot Light After Gas Is Shut Off

Feb 09, Subscribe Now:datlovesdat.com?add_user=ehowatHomeChannelWatch More:datlovesdat.com a hot water. First, you need to access the pilot light burner. It might be exposed already, or you might have to open a cover to reach it. Either way, your water heater pilot light should be located near the water heaters gas knob underneath its gas valve. Once you have the pilot light cover openif your water heater has onefind the burner.

On some gas-powered appliances -- such as gas ranges, water heaters, boilers and gas fireplaces -- the pilot light works to ignite the main how to reignite a gas water heater when the gas is switched on to the burner by the regulating valve. If the pilot light is not lit, the gas burner will not ignite, which could cause a dangerous situation by letting highly flammable gas escape into the air.

If the pilot light goes out, you can relight it after the gas is shut off using a match or the unit's electronic ignitor if it has one, following the proper safety precautions. If your gas is shut off, turn the gas shutoff valves on all gas appliances to the "off" how to reignite a gas water heater until the gas service is restored.

Use a flashlight to locate the valve if you cannot find it. To turn off the valve, rotate it clockwise until the valve stops turning. If you smell gas in the house, put out any potential ignition materials such as candles or cigarettes, and open windows and doors for the house to ventilate.

Once gas service is restored, how to capture images from video the control knob on the gas appliance, and turn it to the "off" position. Then turn the gas control valve knob for the appliance on by how to safely pop a pimple it counter-clockwise until it stops turning.

Remove the front cover of the appliance to access the pilot light area. Some appliances, such as a gas fireplace, may have an open pilot light area. Use a screwdriver how to increase eye vision power remove the screws to open the panel if needed. Turn the pilot control knob to the "pilot" position.

Light a match and hold it directly how to reignite a gas water heater the tube in the pilot opening. Press and hold the pilot control knob down until the flame lights. Remove the match, but continue to hold the knob down for 30 seconds before releasing it. If the pilot light flame does not stay lit after releasing the knob, repeat the process. If after repeated attempts the pilot will still not stay lit, turn the knob to "off" and contact a technician. Once the pilot light stays lit, rotate the pilot control knob to the "on" position, and confirm that the main burner is lit.

Replace the pilot light panel cover and repeat the steps for any other gas appliances with pilot lights that need to be lit. If the gas appliance is equipped with an electronic spark ignitor, you don't need a match to light the pilot light. Instead, click the ignitor button while holding down the pilot knob until the pilot light is ignited.

Hold the pilot knob down for 30 seconds before releasing and checking that the pilot light remains lit. If you smell gas anywhere in the home, do not attempt to light the pilot light without first finding and turning off the source of the gas leak and ventilating your home thoroughly.

Chris Baylor has been writing about various topics, focusing primarily on woodworking, since By Chris Baylor Updated December 17, Related Articles. Tip If the gas appliance is equipped with an electronic spark ignitor, you don't need a match to light the pilot light. Warning If you smell gas anywhere in the home, do not attempt to light the pilot light without first finding and turning off the source of the gas leak and ventilating your home thoroughly.

References UsePropane.

Related Posts

How to Reignite a Hot Water Heater 1. Turn the control knob on the heater to the "Off" position. Wait five minutes to clear residual gas or oil from the 2. Remove the white cover at the lower portion of the tank below the control knob by hand. Lift out the metal burner 3. Depress and hold down.

The pilot light of your water heater is a small lit flame. When you are looking at the outside of your water heater, look for a pipe that enters the water heater tank from the outside. The location of the pilot light should be recognizable by the gas knobwhich is usually redthat is located on the surface of a metal box attached to the outside of the water heater. The flame that lights the pilot light should either be already exposed or will be visible once you open the door of the pilot light cover.

That means, when the pilot light is off, you will have no hot water for hot showers , no hot water to wash dishes, etc. In fact, the most common cause for a pilot light unexpectedly going out is a natural change in gas pressure that extinguishes the pilot light flame.

It requires no tools except possibly a lighterand maybe not even that, depending on the type of water heater you have. First, you need to access the pilot light burner.

It might be exposed already, or you might have to open a cover to reach it. Once you have the pilot light cover openif your water heater has onefind the burner. You might need a flashlight for this step. Look out for two small gas tubes, which should lead directly to the pilot light burner. To actually light the pilot light flame, you may need a long lighter. If your water heater has an igniting buttonusually the button is either red or blackyou can press that to ignite the flame.

If your water heater does not have an igniting button, light the burner using a long lighterlike the kind you use to light a candle. Finally, hold the gas knob down for a full minute before slowly releasing it to make sure the flame stays lit. While your water heater pilot light going out is most commonly just a result of a natural change in gas pressure, there are many different less common problems that can cause a pilot light to go out.

Depending on the root cause of the extinguished flame, reigniting your water heater pilot light is not always possible on your own. If the methods detailed in this post do not work for you or if your water heater pilot light going out is a recurring problem, give a professional plumbing company in your area a call.

Accurate Leak Locators and Plumbing is a family-owned, professional leak location and plumbing service company that proudly serves customers throughout the Inland Empire, San Diego County, Orange County, Los Angeles, and beyond with any and every plumbing and leak location issue.

What is a Water Heater Pilot Light? Related Posts. How to Properly Clean Shower Heads. How to Repair a Leaking Faucet. How to Solve High Water Bills. Close Sliding Bar Area. Main Office Illinois Ave. Go to Top.



More articles in this category:
<- How to conference call on landline - How to design a cover page in photoshop->

5 thoughts on “How to reignite a gas water heater

Add a comment

Your email will not be published. Required fields are marked *

Back to top